8 inch ford rear end identification.

Jan 22, 2024 · In summary, Ford’s 8-inch and 9-inch rear differentials have left an indelible mark on the automotive industry. The 8-inch differential, with its standard and 8.8-inch variants, offers a versatile solution for a range of vehicles. Meanwhile, the 9-inch differential, available in standard, nodular iron case, and aluminum case versions ... Ford Rear Axle Assembly Identification - Page 13. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L. The 8.8-inch is 30 percent stronger than the 71/2-inch, and the axle is a sturdy 31/4 inches in diameter. It can be used reliably in 300hp or better powertrains. Finding a donor car or truck for an 8.8-inch differential should be relatively easy. Just about any Ford light truck newer than 1983, or passenger car newer than 1986 up into the late ...Housing Identification. 57 - no dimples, flat center band up the center of the rear cover, bottom drain plug. 58-59 - two dimples on back of housing, flat center band, some had drain holes. 60-67 - two dimples, flat center band, oil level hole in back cover. 63-77 Lincoln, LTD, Thunderbirds had 9.375 inch centers, housings were cut away at the ...So here, thanks to Mike and ND, is the corrected graphic on decoding the axle tag on dents with 9" rear axles. 5MB: The 5 refers to the fifth year, M refers to December and B refers to the second week of that month. Thus, the date of manufacture is Second Week (day 8-12) of December, 1975.

62 posts · Joined 2003. #1 · Apr 20, 2003. I've got a third member out of a 9 inch ford that I don't know what kind of gear ratio it has. There is no tag on the housing. I know that it is a 31 spline set up. The info stamped on the outer surface of the ring gear is: Ford USA D2AW 4210 AX2. The ring gear hub has stamped on it: C6AW 4205 B, and ...GM 9.76" 12 Bolt Rear, 2014-On. GM 10.5" Rear. GM 11.5" Rear End. GM Dana 60. GM / Chevy - Differential Identification Shop by your differential. Please select a rear end that matches your vehicle below. General Motors has a wide range of front and rear ends! We carry everything from the 7.25" IFS front end parts, to the large 11.5" rear ...Ford 9 inch rear end identification is easy and can be accomplished with nothing more than a deep socket as a “go-no-go” gauge for the bottom two retaining nuts on the center section. If the socket fits (as shown in our photo below) it is a Ford 8-inch housing. The 9-inch housing’s center section will not allow the socket to clear, and ...

I bought a Ford 8-inch rear and installed it in my '40 Ford with my own 4-bar and coil-overs. When it came time to redo the brakes, I found the the shoes were 10" dia. x 2" wide. I haven't found any Ford listing that has 2" wide shoes. They are either 1-3/4" or 2-1/2" wide. I got some 2" wide shoes by looking up Bendix shoes at NAPA and they ...

Ford nine inch differential cases +. vertical ribs and no "N" Standard'tase C. Case m arkînìv MJ29h3 case No tiller plug in rósing. N Date Note two vertical ribs and "N" N cases prior to 1969 did not have the arking arking, With fill plug sung number buas C4AúU-AB. Standard g" Case CIA)V-E Note single vertical rib and til Case.Aug 25, 2020 ... On todays episode of Explained, we go over the main differences between a Ford 9-Inch and a GM 12-Bolt rearend and which application may ...Received 0 Likes on 0 Posts. How to read the tag on a Ford 8.8" Rear. The 3 31 means you have a 3.31 gear in that rear end. The space is for a L, which would make it a limited slip rear end. My rearend has a 3L55 which is a limited slip 3.55, but my friends is just a 3 55.Aug 16, 2021 · Thanks again everybody for the help. How To Recognize 9-Inch Housing Centers: 1957 - no dimples, flat center band up the center of the rear cover, bottom drain plug. 1958-1959 - two dimples on back of housing, flat center band, some had drain holes. 1960-1967 - two dimples, flat center band, oil level hole in back cover.

Ark survival evolved map caves

The Chevy’s rear axle code contains information on the vehicle’s gear ratio, date of manufacture and the rear axle assembly plant. The prefix on the code consists of two letters fo...

Ford 8 inch limited slip diff options. Hey all, it's been a while, but I'm still kickin' around. Anyways, It's time to start ordering parts and I've got a few questions. 1. I'm rebuilding an 8'' rear end because my little 289 hasn't broken 300 hp and probably won't for a while. I've been looking and really need some advice as to who makes the ...Here is a list of rear ends that I picked up some time ago on the Fordnatics mailing list. These measurements are from flange to flange. Subtract 5" for bare housing length. 65-66 Mustang 57.25 inches. 67-70 Mustang 59.25 inches. 71-73 Mustang 61.25 inches. 77-81 Versailles 58.50 inches. 74 Maverick 8" 56.50 inches.Ford Rear Axle Assembly Identification - Page 10: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: C001-A: Crown Victoria, Grand Marquis 92-93: 3.55: 8.8: L: 28 : C002-A:Step 22: Fill Differential with Fluid. If you have a limited-slip differential, add 4 ounces of correct friction modifi er. Typically for the 8.8- inch axle, the fill amount is about 2½ quarts to the bottom of the fi ll hole when the vehicle is level. This photo shows the fill hole with the 3/8-inch square drive plug.mustangboy. 6653 posts · Joined 2002. #2 · Feb 2, 2002. No the 8 and 8.8 rears are not the same.The 8inch is basically just a slightly smaller version of the 9 inch. The 8 and 9 inch rears have removable "pots" that go into the front of the axle housing as a complete assembly.The 7.5 and 8.8 rears used in the newer Fords have a cover that ...I've got a stock Ford 8" LSD that is measuring .030" backlash. There appears to be no abnormal wear on the teeth. I've never driven the car ('67 Fairlane) so I don't know if the rear end made any noise. I know the bearings are supposed to have a pre-load of .005" which is equivalent to moving one hole in the side adjusters.

Ford 8" Rear Pinion Yoke. $97.98 (1 review) Write a Review. SKU: 3104-252 Shipping: $15.00 (Fixed Shipping Cost) Current Stock: Quantity: Decrease Quantity: Increase Quantity: Wishlist. Share This Article. Overview; Reviews; Product Description. This 1310 Pinion Yoke Fits Ford 8" Models . Don't Forget to Add the U-Bolt Kit Below! ...Differential Identification using Tags & Stampings. The most accurate differential identification is provided by the bottom line of the tag number or axle tube stamp. … Ford 8.0 Ring and Pinion Part Number, Tooth Count & Ratio. Your gears run cooler and last longer! Order above high performance synthetic oil and friction additive combo kit at time of order for ring and pinion or bearing overhaul kit and pay only $63.95 plus S&H, a $69.00 value. This is just a simple video part of the ls Swap Jeep Ford 8.8 axle build showing what the axle tag means.First, step up to a '67-and-up axle housing, shortened to the correct width for a '65-'66 Mustang. Second, grab a '67-and-up chunk and stuff it into the modified housing. And finally, fit the iron ...

Oct 21, 2023 ... DIY HOW TO Ford 8 and 9inch rear end disassembly in under 15 minutes! In this video we start PART 1 of the replacement of my Ford 8" third ...The listing has more than 2900 axle ID codes and covers virtually EVERY rear-wheel-drive differential in every Ford car, light truck, van and SUV from 1963 through 2001. Page 01 - WBG-E thru WCN-L. Page 02 - WCN-M thru WDC-Z. Page 03 - WDD-B thru WDN-DR.

Ford Rear Axle Assembly Identification - Page 01. NOTE: Axle tag location …The 60-63 are the same basic body style. A 63 with a V8 was 56 inches from mounting surface to mounting surface. The narrowest 8 inch ford ever made. With the granada rear, you will not be able to use a standard mag wheel such as a torque thruster or crager ( 3 & 3/8 inch back space on a 6 inch wheel) unless you are using a 185 series skinny ...First, check to make sure you have a 5 x 4.5 bolt pattern, some 9 inch rears in cars had 5 x 5 bolt patterns. Measure the width of the backing plate, it should be 10 or 11 inches, most likely it is 10 inches. Lay a flat edge across the axle flange and measure the distance to the backing plate, this will tell you the width of the brake drum.S424F is a 1989 NUMBER.....The S stands for Sterling plant. S is just a prefix number. F is a suffix number. Most 8.8's were produced by the Sterling axle Plant. The few that were not came from the Van **** plant 3.27.....gear ratio A88.....The A should stand for 1 which is non limited slip differential. The 88 is 8.8 rearJan 22, 2024 · In summary, Ford’s 8-inch and 9-inch rear differentials have left an indelible mark on the automotive industry. The 8-inch differential, with its standard and 8.8-inch variants, offers a versatile solution for a range of vehicles. Meanwhile, the 9-inch differential, available in standard, nodular iron case, and aluminum case versions ... Dodge Ram pickup tricks come equipped from the factory with a stereo system that includes rear speakers mounted in the rear side trim panels. If you want to install new speakers in...2010-2011 Ford Ranger 8.8-inch Axle - 58.50 inches *. 1991-2003 Ford Explorer 8.8-Inch Axle - 59.625 inches. * The 2010-2011 Ford Ranger 8.8-inch axle is actually narrower and has shorter shafts than the 2009 and earlier models. Ford used rear disc brakes on the 2010-2011 Rangers, so Ford Shortened the axle housing and shafts to compensate for ...

Hold rel mem cr pending chase

The short answer is yes, you have a 9.75 (you probably also have a 5.4L engine). The number and possible letter that is under the bolt head should be a 3. So if it reads 3 55 9 75 OK31, then you have a 3.55 gear and a 9.75 open rear end. if its 3L55 9 75 OK31, then you have a 3.55 gear and a 9.75 limited slip rear end.

Yes a 69-77 Ford Maverick 8" rear is 56.5" wide and a Granada/Versailles 77-81 is 58" wide both good rearends for a Model A the Maverick is best with fenders. Most 56 Ford rearends were around 61" wide except the 57-59 Ranchero or wagon 9" at 57.25" wide. All mesurments are from wheel flange to wheel flange.The code can be found on the Vehicle Identification Number (VIN) label, which is typically located on the driver's side door jamb or the front windshield. 2. Decoding the Axle Code. To decode the Ford Axle Code, you need to refer to the manufacturer's specifications or consult an online decoding tool. The code is made up of several ...This Ford (9" gasket also fits 9-3/8" gear cases, and shows where teh notches in teh housing go to clear the ring gear. You can place the gasket, mark the housing, and cut the clearance notches. Clean everything really well and run a magnet around to get all the metal chips out: -=≡ If it was easy, everyone would do it ≡=-.The pinion in a standard 9-inch sits about 2 1/4 inches below the axle centerline, while the pinion in a reverse-rotation 9-inch is about 1 1/4 inches above the centerline. Those 3 1/2 inches can ...The 8 inch should have sealed ball bearings, which are not suppose to have any play in them. I think you have a bad bearing. You need to check it out before driving anymore. Like. J. junkyardjeff Discussion starter. 293 posts · Joined 2004. #3 · Dec 1, 2009. The bearings have less then 4000 miles on them.You also need to be aware of axle offset which is 2-3/8". While I have not tried, been led to believe up to 66 Ford backing plates/brakes will work, so you should …My video on how to change the gear oil in a rear differential or rear end. These are universal instructions for most vehicles. It is an easy repair or replac...Yes a 69-77 Ford Maverick 8" rear is 56.5" wide and a Granada/Versailles 77-81 is 58" wide both good rearends for a Model A the Maverick is best with fenders. Most 56 Ford rearends were around 61" wide except the 57-59 Ranchero or wagon 9" at 57.25" wide. All mesurments are from wheel flange to wheel flange.This means that new spring perches need to be welded on top of the Explorer's 8.8-inch axle, and they have to be spaced and angled to match your application. However, the Ford Ranger FX4 8.8-inch axle is a bolt in swap. But not all Ford Ranger FX4's have the 31-spline rear axles. From 2003-2007, ford offered (2) versions of the Ford Ranger FX4:The 8.8-inch is 30 percent stronger than the 71/2-inch, and the axle is a sturdy 31/4 inches in diameter. It can be used reliably in 300hp or better powertrains. Finding a donor car or truck for an 8.8-inch differential should be relatively easy. Just about any Ford light truck newer than 1983, or passenger car newer than 1986 up into the late ...

Ford Rear Axle Assembly Identification - Page 04: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDM-E: Ford Pickup '63-'72 F-100: 3.25: 9 in: NL: 28-WDM-F: Ford Pickup '63-'72 F-100: 3.50: 9 in: NL: 28-WDM-H: The code appears as a number or letter/number combination in the 'Axle' column of the label. If you look at the 'AXLE' section on the label above, you'll see that this Ranger has a 'F7' axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer and Aerostar ... I've got a stock Ford 8" LSD that is measuring .030" backlash. There appears to be no abnormal wear on the teeth. I've never driven the car ('67 Fairlane) so I don't know if the rear end made any noise. I know the bearings are supposed to have a pre-load of .005" which is equivalent to moving one hole in the side adjusters.Instagram:https://instagram. best shotgun for clay targets The listing has more than 2900 axle ID codes and covers virtually EVERY rear-wheel-drive differential in every Ford car, light truck, van and SUV from 1963 through 2001. Page 01 - WBG-E thru WCN-L. Page 02 - WCN-M thru WDC-Z. Page 03 - WDD-B thru WDN-DR. carmax houston cars under dollar10000 Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L. harry potter's girlfriend crossword Ford 8-inch rearend: good ol' spot repairChevy truck rear axle identification Ford 8.8-inch axle builder's guideBasic id ford 9 inch, rear, 8 inch rear end,carrier, center section. Rear axle ford 1986 rod brakes 1994 disc 1993 had hot five mustangs scrounger guide svo some hotrodChevy rear axle identification Ford maverick 8" rear endThe ...To the best of my knowledge ford never made a factory true "posi" rear end. It shoudl either be a limited slip or an open differential. All you have to do is get both sides off the ground and turn one side. If the other side goes in the same direction it is either a factory limited slip or possibly has a spool installed or the spider gears ... gloss lake wylie 9” third members are limited-slip differentials. They are available in either a standard case, nodular case, or an aluminum thru-bolt for street to race applications. Of these Ford rear differentials, either a 28, 31, 35 or 40 spline axle can be used. All third members come with a new housing gasket, and all trac-lok units come with a ...7.5" vs 8.8" Rear Ends. The cover shape difference between 7.5" and 8.8" is the quickest way to identify an 8.8" from a 7.5" rear end. The 8.8" rear end is flat on the top and the bottom as well as the left and right. It has a square design with four rounded corners and ten bolts. When measuring from the top left bolt to the ... dale earnhardt monopoly unopened Like the 9-inch, the Ford 8-inch is a third member-type carrier assembly for the banjo-type rearend. This means it unloads from the front and utilizes a third pinion bearing to give it extra support. This extra support helps reduce twisting of the differential when under load. The 8-inch uses the same axles as the larger 9-inch, which adds to ...The following axle identification is based on the axle tag located on the axle, ... The rear axle is of the banjo housing, hypoid gear-type using an 8, 8-3/4, or 9-inch ring gear, in which the centerline of the pinion is mounted below the centerline of the ring gear (Fig. ... Due to Ford listing multiple car models together, some of the axles ... what bank is dayforce wallet Location: Williamsport PA, MAFB NJ. Posts: 77. Likes: 0. Received 0 Likes on 0 Posts. Rear End Tag Identification. Hello all I am curremtly in the process of restoring my 1982 Ford F-150 XLT Lariat. I have removed everything rear of the cab including the axel. From what I can tell I have a Nine inch rear all though I am not completely sure. ramos pizza rocky mount north carolina A few ways to tell a the difference between a Ford 9" rear end and a Ford 8" rear end. The main way to tell is the 3rd member is flat on top on a Ford 8 inc...stang6992 said: not being an *** but if im not mistaken there is no such gear as a 3.40 for an 8 inch. there is a 3.25 and a 3.55. but either way. if you do not plan on racing it get a set of 3.25s b/c they are more highway friendly unless you got tall tires. Yes I remember looking for the 3.40 8 inch gears in the junkyards but never found any.How to Measure Ford Rear End Axle Splines, Flange Width and Height Ford 8 Inch and 9 Inch Third Members - Identify 28 and 31 Spline Axles, Yoke Flange Width and Height … extended forecast rehoboth beach delaware Originally introduced by Chrysler in 1957, the 8¾-inch rear was used in many Chrysler car and Dodge truck bodies throughout the years until 1974. These differentials have a removable carrier, which, like the Ford 9-inch, unbolts from the front. It is also referred to as a "banjo-type" differential assembly.Ford Rear Axle Assembly Identification - Page 04: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDM-E: Ford Pickup '63-'72 F-100: 3.25: 9 in: NL: 28-WDM-F: Ford Pickup '63-'72 F-100: 3.50: 9 in: NL: 28-WDM-H: doberman puppies for sale fayetteville nc Ford 8.8 axle. The Ford 8.8 is an automotive axle manufactured by Ford Motor Company at the Sterling Axle Plant in Sterling Heights, MI. It was first used in model year 1983 Ford trucks. The axle was developed to replace the Ford 9-inch axle. This axle is still in production today for a variety of Ford vehicles. Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28- dr rose watseka il 3. Jul 25, 2017. #3. pontiacgp said: That looks like an 8.2 with the 8.5 cover on it. That rear end is 4.5" wider than the G body rear. You'll need conversion uppers and you can use the stock lowers. I bought my conversion uppers from UMI for my 8.2 out of a 67 Chevelle. Roger that Sir, thanks for the information.The question is whether a car has an 8-inch or 9-inch Ford. An identification might be needed while looking for a donor rear in a salvage yard, or trying to find out what is in one’s own car. Some 8″ housings look like the early “smoothy” 9-inch housings, so merely peering under a crusty undercarriage will hinder a correct I.D. how to turn off closed captioning on comcast xfinity It took a couple trips, but we now possess the necessary bits and pieces to put together a reconditioned 8-inch Ford rearend for our customer-friend, Danny …The easiest way to tell is to try to put a socket on the lower bolts. On the 8", the socket goes on straight without hitting the case. On the 9", the socket won't fit this position or the bolt on the other side of center, you'll need to use a wrench to remove those nuts. There is a pocket at the bolt location necessary because of the larger ...